Skip to end of banner
Go to start of banner

0266 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 6 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Tumble Dryer (Stack)
Manufacturer: ADC
Make: Maytag
Model Length: 10

Associated Models


MLG45PDBDS
MLG45PDBWS
MLG45PDBWW
MLG45PDBWW20
MLG45PDCWS
MLG45PDCWW

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0010

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

 I-M0104

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify that included harnesses will reach the desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

 I-M0162

Part #: C-0913

Desc 1: Drop Cover

Desc 2: Maytag Stack Dryer

   Qty: 1

Part #: C-1062

Desc 1: Nut

Desc 2: 4-40 - Kep

   Qty: 4

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

  1. Remove existing coin drop.

  2. Install C-0913 Drop Cover where the coin drop was previously mounted. Secure using (4) C-1062 4-40 Keps Nuts.

  3. Place the C-6700-TEMP Drill Template on the desired mounting location.

  4. Verify that included harnesses will reach the desired location without encountering interference from internal machine components.

  5. Refer to Touchscreen Reader Mounting Guide (F2 & F3) for further instructions.

  6. Optional: Use C-5710 Rubber Grommet to protect harnesses from damage during machine operation if any secondary hole is cut internally to run harnesses to the reader mounting location.

Connect Power

 I-P0014

Part #: C-5203

Desc 1: Power Adapter Harness

Desc 2: High Voltage - Contact

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the FasCard Reader Install - Universal Concepts page by connecting the C-5203 Power Adapter Harness to the Terminal Block.

    1. Brown and Blue wires are interchangeable and connect to L1 and L2.

    2. Secure Green ground wire beneath Green ground screw.

  2. Connect the opposite end of the C-5203 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0019

Part #: C-5361

Desc 1: Coin Sense Harness

Desc 2: Male taps, Rq. Female

   Qty: 1

Part #: C-5260

Desc 1: Wire Tap Bridge

Desc 2: 18-16 AWG

   Qty: 2

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

  1. Disconnect the Coin Drop from the Machine Control Assembly.

    1. This harness must remain disconnected for FasCard to function properly. Reconnecting this harness after installation will damage FasCard reader. Technical Support recommends taping off these connections.

  2. Bridge the solid Red and solid Blue wires coming from the coin eye sensor using the C-5260 Wire Tap Bridge.

  3. Bridge the Blue/Silver and solid Purple wires going to the machine control assembly using the C-5260 Wire Tap Bridge.

  4. Tap the Red, White, and White/Blue wires with the C-5101 Spade Taps provided.

  5. Connect the C-5361 Coin Sense Harness to the installed spade taps.

    1. Red connects to Red.

    2. Blue connects to White/Blue.

    3. White connects to White.

Connect Machine Interface Harness

 I-T0065

Part #: C-5363

Desc 1: Machine Start Harness

Desc 2: Maytag Gen1 Dryer

   Qty: 1

  1. Connect the C-5363 Machine Start Harness to the debit spade connectors on the Machine Control Assembly.

Connect and Mount Reader

 LaundryCard Reader (C-0100, C-0101, C-0102, C-0103)

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  5. Secure the LaundryCard reader to the bracketry using included hardware.

 LaundryCard L2 Reader (C-0103-L2)

L2_Port_Guide.png

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Power Harness to port 1.

  5. Secure the L2 reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F1 Reader (C-5001)

  1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Mounting Guide.

  2. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  3. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

  6. Secure the FasCard reader to base as described in the F1 Reader Mounting Guide.

 F2/FLEX Reader (C-5401, C-5402, C-5402E)

  1. Feed remaining harness ends through the mounting hole as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

  2. For Serial Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

  3. For Pulse Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    1. For dual coin drop setups connect the secondary Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Harness to port 1.

  6. Secure the FasCard reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F3 Reader (C-5520, C-5520E)

TODO

CCI Software Configuration

Machine ControlPulseSerial
Gen1SingleVend (MLV+) / 24ms*NOT SUPPORTED*

Additional Resources

  • No labels