Skip to end of banner
Go to start of banner

3651 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 7 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Stack Washer/Dryer
Manufacturer: Maytag
Make: Maytag
Model Length: 10

Washer and Dryer must be the same vend price

Associated Models


MLE22PDAYW
MLE22PDAYW0
MLE22PRAYW
MLE22PRAYW2
MLG22PDAWW
MLG22PRAWW
MLG22PRBWW

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0010

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to F1 Reader Mounting Guide for further instructions.

 I-M0104

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard F2/F3 Reader Installation Guide - Front Mount for further instructions.

 I-M0200

Part #: C-6982

Desc 1: Maytag MLG22PD Bracket

Desc 2: F2

   Qty: 1

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5436

Desc 1: Screw

Desc 2: 10-32 x 1" - Pan MS

   Qty: 2

Part #:

Desc 1:

Desc 2:

   Qty: 1

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

  1. Remove existing W11034287 Fascia from machine console panel. Remove the coin drop and coin box from the machine.

  2. Insert C-6982 MayTag Adapter Bracket into the coin drop opening and align behind the coin drop bracket so the larger hole is towards the bottom. Then use (2) C-5420 10-32 x 1/4" Pan Screws to secure to the machine.

  3. Install the W11034310 Fascia over the console panel.

  4. Align the C-5414 F2 Standard Mounting Bracket with the holes in the C-6982 MayTag Adapter Bracket and attach together using (2) C-5436 10-32 x 1" Pan Screws.

 I-M0206

Part #: C-5701

Desc 1: F1 Maytag Mounting Bracket

Desc 2: Small chassis stack dryers

   Qty: 1

Part #: C-1060

Desc 1: Screw - Build: TK

Desc 2: 8-32 x 3/8" - Zinc

   Qty: 4

Part #: C-5021

Desc 1: Label

Desc 2: Screw Cover

   Qty: 1

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

Part #: C-5700

Desc 1: Mounting Bracket

Desc 2: Surface Mount

   Qty: 1

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

  1. Remove any cover or card reader plate attached to the payment device mounting bracket.

  2. Place the C-5701 Mounting Plate behind the payment device mounting bracket and align the set of lower mounting points with that of the out set of threaded holes on the C-5701 Mounting Plate. Ensure the inner set of threaded holes are accessible through the central opening in the MayTag payment device bracket. Attach using (2) C-1060 8-32 x 3/8" Screws.

  3. Place the C-5700 Mounting Bracket over the front of the assembly so that the set of circular openings align with the threaded holes of the C-5701 Mounting Plate accessible through the central opening. Attach using the remaining (2) C-1060 8-32 x 3/8" Screws.

 I-M0212

Part #: C-6982

Desc 1: Maytag MLG22PD Bracket

Desc 2: F2

   Qty: 1

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5436

Desc 1: Screw

Desc 2: 10-32 x 1" - Pan MS

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

  1. Insert C-6982 MayTag Adapter Bracket into the payment device opening and align behind the bracket so the larger hole is towards the bottom. Then use (2) C-5420 10-32 x 1/4" Pan Screws to secure to the machine.

  2. Align the C-5414 F2 Standard Mounting Bracket with the holes in the C-6982 MayTag Adapter Bracket and attach together using (2) C-5436 10-32 x 1" Pan Screws.

 I-M0221

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6802

Desc 1: FLEX RF Reader Mounting Kit

Desc 2:

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard F2/F3 Reader Installation Guide - Front Mount for further instructions.

Instructions do not exist for Kit I-M0282

Instructions do not exist for Kit I-M0285

Connect Power

Connect Coin Sense Harness

Connect Machine Interface Harness

 I-T0004

Part #: C-5364

Desc 1: Machine Start Harness

Desc 2: Maytag MFR

   Qty: 1

  1. Connect the C-5364 Machine Start Harness to the AA3 connector on the Machine Control Assembly.

Connect and Mount Reader

Machine Configuration

MayTag AA3/Debit Connection Payment Pulse

  1. Enter Service Mode by activating the service switch.

  2. Locate Coin/Debit Option (J.) and set to Cd.

CCI Software Configuration

Machine ControlPulseSerial
Gen2SingleVend (MLV+) / 24ms*NOT SUPPORTED*

Additional Resources

  • No labels