Skip to end of banner
Go to start of banner

3569 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 11 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Top Load Washer
Manufacturer: Alliance
Make: [VARIES]
Model Length: 15

For coin prepped models in card only installations, customers will need to confirm if the metercase is standard or high capacity to determine which mounting kit to send.

Associated Models

HWNBC2PP115PW01
HWNBC2PP115TW01
HWNBC2SP113TW01
HWNBC2SP115TW01
HWNBY2PP115TW01
HWNBY2PT115TW01
HWNBY2SB115EW01
HWNBY2SP115TW01
HWNKC210115TW01
HWNKC2FP115TW01
HWNKC2P1115TW01
HWNKC2SB115TW01
HWNKC2SE115TW01
HWNKC2SP115PW01
HWNKC2SP115TW01
HWNKC2SP116CW01
HWNKC2SP116EW01
HWNKC2SP116TW01
HWNKC2ST115PW01
HWNKC2ST115TW01
HWNKC2ST116TW01
HWNKE2SP115CW01
HWNKE2SP115EW01
HWNKX2SP115CW01
HWNKY2SB115CW01
HWNKY2SP115CW01
HWNKY2SP115TW01
HWNKY2SP116CW01
HWNKY2SP116TW01
HWNKY2ST115CW01
HWNKY2ST116CW01
HWNNE2AP113CW01
HWNNY2SP113CW01
HWNSX25P115TW01
HWNSX2PP115TW01
HWNSX2SP115TW01
HWNSX2ST115TW01
KWNBX2SP113TW01
KWNBX2SP115PW01
KWNBX2SP115TW01
KWNBX2SP116TW01
KWNSX2PP115TW01
KWNSX2SP115TW01
PWNBC2PP115TW02
PWNBX2PP115TG02
SWNMC2HP115TW02
SWNNC25P113TW01
SWNNC2AP113TW01
SWNNC2FP115TW01
SWNNC2HP113TW01
SWNNC2HP113TW15
SWNNC2HP115TW01
SWNNC2HP115TW02
SWNNC2HP116TW01
SWNNC2HT115TW01
SWNNC2HT115TW02
SWNNC2KP113TW15
SWNNC2PP113TW01
SWNNC2PP113TW02
SWNNC2SP113TQ01
SWNNC2SP113TW01
SWNNC2SP113TW02
SWNNC2SP113TW03
SWNNC2SP114TW01
SWNNC2SP115TQ01
SWNNC2SP115TW01
SWNNC2SP115TW02
SWNNC2SP116CW01
SWNNC2SP116TW01
SWNNX2AP113TW15
SWNNX2HP115TW01
SWNNX2HP116TW01
SWNNX2SP113TW02
SWNNX2SP115CW01
SWNNX2SP115TW01
SWNNX2SP115TW02
SWNNX2SP116TW01
SWNNY21SP15TW01
SWNNY2HP115CW01
SWNNY2HP115TW01
SWNNY2HP116TW01
SWNNY2SG115TW01
SWNNY2SP113TW01
SWNNY2SP115PW01
SWNNY2SP115TW01
SWNNY2SP116TW01
SWNNY2ST113TW01
SWNNY2ST115TW01
SWNSX28P115TW02
SWNSX2SB115DW02
SWNSX2SP113TW02
SWNSX2SP115TW01
SWNSX2SP115TW02
SWNWC2HP115TW42
SWSNX2SP115TW02
TWNBC2PP115TW02

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

Connect Power

Connect Coin Sense Harness

 I-S0027

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: F2

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

 I-S0031

Part #: C-6253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

  1. Disconnect the harness from micro switch.

  2. Connect both ends of C-6253 Coin Sense Harness to the micro switch.

Connect Machine Interface Harness

Connect and Mount Reader

Machine Configuration

ACA Controls

  1. Locate the dip switch on the back of the machine's control board.

  2. Set dip switch 3 to the ON position. 

  3. Leave all other dip switches as is.

Titanium Controls

  1. Enter Manual Mode by opening the service door and closing the coin vault switch. Then press the following two buttons based on the control:

    Quantum Gold Pro (T4)

    MDC II (T1)

    Regular & Normal

    Normal Hot & Perm Press Warm

  2. rAPid will be displayed on the control. Select the Prog option and then configure the following settings:

    1. Serial Payment Configuration (SErPAY): Card

    2. Card Enable (CArdEn): On

  3. Exit Manual Mode.

CCI Software Configuration

Machine ControlPulseSerial
Coin Slide Hybrid (Pulse)SingleVend (Relay) / 80ms*NOT SUPPORTED*
Galaxy 600 (A2)SingleVend (MLV+) / 80msAlliance ACA H7S Top Load Washer A1 - MDC II
MDC II (A1)SingleVend (MLV+) / 80msAlliance ACA H7S Top Load Washer A1 - MDC II
Nonmetered*NOT SUPPORTED**NOT SUPPORTED*
Quantum+ (A4)SingleVend (MLV+) / 80msAlliance ACA H7S Top Load Washer A11 - Quantum+ LL
Quantum+ (A4)SingleVend (MLV+) / 80msAlliance ACA H7S Top Load Washer A4 - Quantum+
Titanium (T1)SingleVend (MLV+) / 80msAlliance Titanium Top Load Washer T1
Titanium (T4)SingleVend (MLV+) / 80msAlliance Titanium Top Load Washer T4

Additional Resources

  • No labels