3418 Reader Install Guide

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer
Manufacturer: Whirlpool
Make: Whirlpool
Model Length: 9 to 10

Card Only Model

Associated Models

CHW9160GW0
CHW9160GW1

Recommended Tools and Supplies

Drill
1 1/8" Tungsten Carbide Tipped Hole Cutter
Cutting Oil
9/64" Drill Bit
Center Punch
Hammer
Fine Point Permanent Marker
Pliers
Tape Measure

Installation

Install Mounting Hardware

I-M0134

Part #: C-5800

Desc 1: F1 Reader Mounting Kit

Desc 2: Universal

Qty: 1

Remove the (4) security torx retaining screws on the front of the machine.
Remove the soap tray by pulling it out and pressing on the retaining tab in the rear of the tray.
Locate and remove the (2) security torx screws inside the soap tray opening.
Remove the final (2) torx screws to open the top cover.
Locate a spot on top of the machine to mount the reader. Verify included harnesses will reach desired location without encountering interference from internal machine components. Mark the location using C-5700-TEMP Drill Template.
Refer to F1 Reader Mounting Guide for instructions on drilling mounting holes and mounting the reader.

I-M0136

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

Qty: 1

Remove the (4) security torx retaining screws on the front of the machine.
Remove the soap tray by pulling it out and pressing on the retaining tab in the rear of the tray.
Locate and remove the (2) security torx screws inside the soap tray opening.
Remove the final (2) torx screws to open the top cover.
Locate a spot on top of the machine to mount the reader. Verify included harnesses will reach desired location without encountering interference from internal machine components. Mark the location using C-6700-TEMP Drill Template.
Refer to F2 Reader Mounting Guide for instructions on drilling mounting holes and mounting the reader.

Connect Power

I-P0007

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

Qty: 2

Part #: C-5336

Desc 1: Power Adapter Harness

Desc 2: Dexter Stack

Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

Qty: 1

Locate the incoming power cables in the rear of the machine. This should include a white, black and green wire.
Use the C-5101 Spade Taps to tap the black (L1) and white (Neutral) wires.
Attach the spade ends of the C-5336 Power Adapter Harness to the taps. Blue to black, and Brown to White.
Attach the Green ground wire from the C-5336 Power Adapter Harness to a nearby chassis ground screw.
Connect the 3-pin connector from the C-5336 Power Adapter Harness to the 3-pin connector on the C-5602R1 Power Converter.
Connect the 4-pin connector from the C-5602R1 Power Converter to the 4-pin connector on the C-5500 Power Extension Harness.
Mount the C-5602R1 Power Converter in the machine by using zip ties to secure it to the machine's wire harness.