3581 Reader Install Guide

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Small Dryer (Single)
Manufacturer: Alliance
Make: [VARIES]
Model Length: 15

Associated Models

HDCBYRGS113CW01
HDEBCAGS173TW01
HDEBCRGS173TW01
HDEBCRGS175TW01
HDEBCRGS176TW01
HDEBYAGS173CW01
HDEBYAGS173TW01
HDEBYRGS116TW01
HDEBYRGS173TW01
HDESXRGS173TW01
HDGBCAGF116TW01
HDGBCAGS113TW01
HDGBCAGS116TW01
HDGBCASG116TW01
HDGBCRGF113TW01
HDGBCRGS113TW01
HDGBCRGS116EW01
HDGBCRGS116GW01
HDGBCRGS116TW01
HDGBYAGS113CW01
HDGBYAGS113TW01
HDGBYASP116TW01
HDGBYRGS1130T01
HDGBYRGS113TW01
HDGBYRGS116TW01
HDGSXRGS113TW01
HDSBYRGS116TW01
KDEBXRGS176TW01
KDESXAGS173YW01
KDESXRGS173TW01
KDGBXRGS115TW01
KDGBXRGS116TW01
KDNBXRGS173PW01
SDENCAGS1732W01
SDENCAGS173TW01
SDENCAGS176TW01
SDENCRGS173TW01
SDENCRGS173TW02
SDENCRGS176TW01
SDENXRGS173TW01
SDENYAGF173TW01
SDENYAGS103TW01
SDENYAGS116TW01
SDENYAGS153TW01
SDENYAGS1732W01
SDENYAGS173TW01
SDENYAGS176FW01
SDENYAGS176TW01
SDENYRGS173TW01
SDENYRGS176TW01
SDESXRGS173TW01
SDGNCAGS113TW01
SDGNCAGS116TW01
SDGNCAGS173PW01
SDGNCRGS113TW01
SDGNCRGS113TW02
SDGNCRGS116TW01
SDGNXRGS113TW02
SDGNXRGS116TW01
SDGNYAGS113TW01
SDGNYAGS116TW01
SDGNYRGF116TW01
SDGNYRGS113TW01
SDGNYRGS116TW01
SDGSXR2G113TW01
SDGSXRGF113EW01
SDGSXRGS113TW01
SDGSXRGS113TW02
SDGSXRSP115TW02

Recommended Tools and Supplies

Drill
1 1/8" Tungsten Carbide Tipped Hole Cutter
Cutting Oil
9/64" Drill Bit
Center Punch
Hammer
Fine Point Permanent Marker
Pliers
Tape Measure

Installation

Install Mounting Hardware

Kit 0 does not exist

Connect Power

Connect Coin Sense Harness

I-S0027

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: F2

Qty: 1

Disconnect the Coin Drop from the Machine Control Assembly.
Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Connect and Mount Reader

Machine Configuration

ACA Controls

Locate the dip switch on the back of the machine's control board.
Set dip switch 3 to the ON position.
Leave all other dip switches as is.

Titanium Controls

Enter Manual Mode by opening the service door and closing the coin vault switch. Then press the following two buttons based on the control:
Quantum Gold Pro (T4)
Galaxy 600 Pro (T2)
MDC II (T1)
High Temp & Med Temp High Temp & Med Temp
High Temp & Med Temp
rAPid will be displayed on the control. Select the Prog option and then configure the following settings:
1. Serial Payment Configuration (SErPAY): Card
2. Card Enable (CArdEn): On
Exit Manual Mode.

CCI Software Configuration

Machine Control	Pulse	Serial
Coin Slide Hybrid (Pulse)	SingleVend (Relay) / -80ms	NOT SUPPORTED
MDC II (A1)	SingleVend (MLV+) / 80ms	Alliance ACA H7S Small Dryer A1 - MDC II
Quantum+ (A4)	SingleVend (MLV+) / 80ms	Alliance ACA H7S Small Dryer A4 - Quantum+
Titanium (T1)	SingleVend (MLV+) / 80ms	Alliance Titanium Small Dryer T1
Titanium (T4)	SingleVend (MLV+) / 80ms	Alliance Titanium Small Dryer T4