Skip to end of banner
Go to start of banner

3444 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 6 Current »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Vending
Manufacturer: Crane
Make: Crane
Model Length: Not Set

Associated Models

123
123C

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0037

Part #: C-0014S

Desc 1: Label

Desc 2: TD LC Window

   Qty: 1

Part #: C-0015S

Desc 1: Label

Desc 2: TD30 Insert Card Graphic

   Qty: 1

Part #: C-0974

Desc 1: Flat Mount Bezel

Desc 2: Fits 3-1/2" x 4-1/4" Opening

   Qty: 1

Part #: C-1042

Desc 1: Nut

Desc 2: 8-32 - Kep

   Qty: 4

  1. Remove payment device bay cover plate if still installed.

  2. Take LaundryCard Reader and remove the front bezel by unscrewing the four screws around the card slot.

  3. Attach the LaundryCard Reader to the C-0974 Flat Mount Bezel using the previously removed screws.

  4. Install C-0974 Flat Mount Bezel into the Payment Device Bay and secure using the C-1042 Kep Nuts.

  5. Apply the C-0014S Window Label over the display opening of the C-0974 Flat Mount Bezel.

  6. Apply the C-0015S Insert Card Label over the card slot opening of the C-0974 Flat Mount Bezel.

 I-M0174

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard F2/F3 Reader Installation Guide - Front Mount for further instructions.

 I-M0178

Part #: C-0939

Desc 1: Bill Acceptor Cover

Desc 2:

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Optional: Remove existing payment device and cover opening using C-0939 BNA Cover Plate.

  2. Place the C-6700-TEMP Drill Template on the desired mounting location.

    1. If C-0939 BNA Cover Plate is used, drilling mounting holes into the plate is recommended if able.

  3. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  4. Refer to FasCard F2/F3 Reader Installation Guide - Front Mount for further instructions.

Instructions do not exist for Kit I-M0270

 I-M0272

Part #: C-0939

Desc 1: Bill Acceptor Cover

Desc 2:

   Qty: 1

Part #: C-6802

Desc 1: FLEX RF Reader Mounting Kit

Desc 2:

   Qty: 1

  1. Remove existing payment device and cover opening using C-0939 BNA Cover Plate.

  2. Place the C-6700-TEMP Drill Template on the desired mounting location.

    1. If C-0939 BNA Cover Plate is used, drilling mounting holes into the plate is recommended if able.

  3. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  4. Refer to FasCard F2/F3 Reader Installation Guide - Front Mount for further instructions.

Connect Power

 I-C0020

Part #: C-6124-MDB

Desc 1: Machine Start Harness

Desc 2: F2 MDB Interface Harness

   Qty: 1

  1. Connect the male, 6-pin connector from the C-6124-MDB Machine Start Harness to the MDB connection on the Machine Control Assembly.

  2. Optional (FasCard Only): Use the female, 6-pin pigtail connector from the C-6124-MDB to reconnect any existing payment devices.

Power is supplied through the same Machine Interface Harness described in step 4.

Connect Coin Sense Harness

No COIN SENSE kits exist for this equipment.

Not applicable in this setup. FasCard reader does not collect payment from any other devices, and will only send funds to the machine's control.

Connect Machine Interface Harness

 I-T0071

Part #: C-0124-MLV

Desc 1: Machine Start Harness

Desc 2: MDB Communication

   Qty: 1

  1. Connect the C-0124-MLV Machine Start Harness to the MDB connector on the Machine Control Assembly.

  2. FasCard Only: Use the pigtail connection to reconnect existing devices.

 I-C0020

Part #: C-6124-MDB

Desc 1: Machine Start Harness

Desc 2: F2 MDB Interface Harness

   Qty: 1

  1. Connect the male, 6-pin connector from the C-6124-MDB Machine Start Harness to the MDB connection on the Machine Control Assembly.

  2. Optional (FasCard Only): Use the female, 6-pin pigtail connector from the C-6124-MDB to reconnect any existing payment devices.

Connect and Mount Reader

 LaundryCard Reader (C-0100, C-0101, C-0102, C-0103)

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  5. Secure the LaundryCard reader to the bracketry using included hardware.

 LaundryCard L2 Reader (C-0103-L2)

L2_Port_Guide.png

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Power Harness to port 1.

  5. Secure the L2 reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F1 Reader (C-5001)

  1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Mounting Guide.

  2. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  3. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

  6. Secure the FasCard reader to base as described in the F1 Reader Mounting Guide.

 F2/FLEX Reader (C-5401, C-5402, C-5402E)

  1. Feed remaining harness ends through the mounting hole as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

  2. For Serial Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

  3. For Pulse Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    1. For dual coin drop setups connect the secondary Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Harness to port 1.

  6. Secure the FasCard reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F3 Reader (C-5520, C-5520E)

TODO

  1. Feed remaining harness ends through the mounting hole as described in the F2 Reader Mounting Guide.

  2. Connect the black, 10-pin connection of the C-6124-MDB Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

  3. Connect the clear, 3-pin connection of the C-6124-MDB Power Harness to port 1.

  4. Secure the FasCard reader to base as described in the F2 Reader Mounting Guide.

CCI Software Configuration

Machine ControlPulseSerial
MDB*NOT SUPPORTED*Vending - MDB Level 1

Additional Resources

  • No labels