Skip to end of banner
Go to start of banner

_Machine Configuration

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 19 Next »



Titanium Controls

  1. Enter Manual Mode by opening the service door and closing the coin vault switch. Then press the following two buttons based on the control:

    Quantum Gold Pro (T4)

    MDC II (T1)

    Regular & Normal

    Normal Hot & Perm Press Warm

  2. rAPid will be displayed on the control. Select the Prog option and then configure the following settings:
    1. Serial Payment Configuration (SErPAY): Card
    2. Card Enable (CArdEn): On
  3. Exit Manual Mode.

MDC Controls

  1. Power off the machine.
  2. Connect the C-0110-CP Jumper Plug to the H2 connection on the Machine Control Assembly.
  3. Power on the machine.

MDC Controls

  1. Power off the machine.
  2. Connect the C-0110-CP Jumper Plug to the H6 connection on the Machine Control Assembly.
  3. Power on the machine.

ACA Controls

  1. Locate the dip switch on the back of the machine's control board.
  2. Set dip switch 3 to the ON position. 
  3. Leave all other dip switches as is.

Centurion Quantum Gold TLW Controls

  1. Power off the machine.
  2. Connect the C-0110-CP Jumper Plug to the H6 connection on the Machine Control Assembly.
  3. Power on the machine.

Titanium Controls

  1. Enter Manual Mode by opening the service door and closing the coin vault switch. Then press the following two buttons based on the control:

    Quantum Gold Pro (T4)

    Galaxy 600 Pro (T2)

    MDC II (T1)

    High Temp & Med TempHigh Temp & Med Temp

    High Temp & Med Temp

  2. rAPid will be displayed on the control. Select the Prog option and then configure the following settings:
    1. Serial Payment Configuration (SErPAY): Card
    2. Card Enable (CArdEn): On
  3. Exit Manual Mode.

Titanium Controls

  1. Enter Manual Mode by opening the service door and closing the coin vault switch. Then press the following two buttons based on the control:

    Quantum Gold Pro (T4)

    Galaxy 600 Pro (T2)

    MDC II (T1)

    Regular & NormalHot & Blankets Cold

    Normal Hot & Perm Press Warm

  2. rAPid will be displayed on the control. Select the Prog option and then configure the following settings:
    1. Serial Payment Configuration (SErPAY): Card
    2. Card Enable (CArdEn): On
  3. Exit Manual Mode.

Titanium Controls

  1. Enter Manual Mode by opening the service door and closing the coin vault switch. Then press the following two buttons based on the control:


    Quantum Gold Pro (T4)

    Galaxy 600 Pro (T2)

    MDC II (T1)

    DryerHigh Temp & Med TempHigh Temp & Med Temp

    High Temp & Med Temp

    WasherRegular & NormalHot & Blankets ColdNormal Hot & Perm Press Warm
  2. rAPid will be displayed on the control. Select the Prog option and then configure the following settings:
    1. Serial Payment Configuration (SErPAY): Card
    2. Card Enable (CArdEn): On
  3. Exit Manual Mode.

MayTag AA3/Debit Connection Payment Pulse

  1. Enter Service Mode by activating the service switch.
  2. Locate Coin/Debit Option (J.) and set to Cd.
  1. Press the Service Switch to enter Service Mode. The display will go blank.
  2. Press the Heavy Soil and Extra Rinse buttons simultaneously. The display will show either "0 00" if in coin mode and "1 00" if in card mode.
  3. If in coin mode, press the Start button. The display will begin flashing.
  4. Press the Cold button to change the left-most digit from "0" to "1".
  5. Press the Start button. The display will stop flashing.
  6. Press the Service Switch to exit Service Mode.

Enhanced Debit (Gen 2)

Enhanced Debit is self-selected when a Generation 2 card reader is installed in the dryer. The Ed option cannot be manually selected or deselected. 

  1. Enter Programming Mode on the machine.

    Card ModelCoin ModelOPL Model
    1. Insert service card.
    2. Display will show L9C1.
    1. Dissemble upper coin box key.
    2. Take out the coin drop from the coin box.
    3. Turn on/off the toggle switch at the back of the coin box.
    4. Display will show L9C1.
    1. Push the 1st & 3rd button at the same time.
    2. Push the 2nd button 3 times.
    3. Push the START button.
    4. Display will show L9C1.
  2. Navigate to StUP>FEA1>VEnd and set to CArd.
  3. Exit Programming Mode.
  1. Connect the washer and open the door. The display will show door.
  2. Press and hold down key 1 until the Cod report appears on the display.
  3. Enter the access code into the menus by pressing the sequence of eight keys of the code without interruption. In basic configuration (when the machine is delivered) the access code to ADVANCED MODE is: 12341234.
  4. If the sequence entered is correct, the display will show Pro, corresponding to the first menu ADVANCED MODE.
  5. Keys 2 and 4 allow the selection of the precedent table menus. The menu selected is shown on the display following its keyword. To enter in it, press key 1 when displaying it.
  6. Navigate to Mod > ID and set value to '1'.
  7. Exit ADVANCE MODE.
  1. Enter the service menu by touch and holding on the top-center of the touch screen for 3 seconds.
    1. Enter password if required.
  2. Configure the machine with the following settings:
    1. Payment Settings:
      1. Card Reader: Enabled
      2. Serial Payment System: Enabled

  • No labels