0466 LaundryCard Reader Install Guide

Owned by Brett Norrell (Deactivated)
Last updated: Jan 24, 2024 by Chris Kite
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Tumble Dryer (Single)
Manufacturer: Alliance
Make: [VARIES]
Model Length: Not Set

Associated Models


JT30XGEC
JT30XGECL0005
JT30XGECN0037
JT30XGMC
JT50CGCDL0004
ST30XGEC
ST30XGMC

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0060

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-5033

Desc 1: Label

Desc 2: 4-5/8" x 3-1/2"

   Qty: 1

Part #: C-0133

Desc 1: Standoff

Desc 2: 8-32" x 1-1/2" - Hex

   Qty: 2

Part #: C-0140

Desc 1: Screw

Desc 2: 8-32 x 3/4" - Cap

   Qty: 2

Part #: C-0936

Desc 1: Vault Mount Bracket

Desc 2:

   Qty: 1

Part #: C-5365

Desc 1: Bypass Harness

Desc 2: Alliance Coin Vault Bypass

   Qty: 1

  1. Remove existing coin box and coin drop.

  2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

  3. Bend the side tabs of the C-0936 Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  4. Attach the C-0133 Standoffs to the Bracket.

  5. Apply the C-0033 Label over the coin drop opening.

Connect Machine Interface Harness

 I-T0008

Part #: C-0109R1

Desc 1: Machine Start Harness

Desc 2: Red / White w. Capacitor

   Qty: 1

  1. Connect the C-0109R1 Machine Start Harness to the Coin1 connection harness on the Machine Control Assembly.

 I-T0082

Part #: C-0113

Desc 1: Machine Start Harness

Desc 2: 2-Wire Harness

   Qty: 1

Part #: C-0122

Desc 1: Spade Taps

Desc 2: 22-18 AWG

   Qty: 2

  1. Connect the C-0122 Spade Taps to the Black and White/Blue wires previously connected to the coin drop.

  2. Connect the C-0113 Machine Start Harness to the two C-0122 Spade Taps.

    1. Start harness wires can be connected to either of the coin drop wires. Pairing does not matter.

Connect and Mount Reader

  1. Feed remaining harness ends through mounting bracket.

  2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  4. Secure the LaundryCard reader to the bracket using included hardware.

Machine Configuration

TODO

CCI Software Configuration

Machine ControlPulseSerial
EDCSingleVend (Relay) / 80*NOT SUPPORTED*
Nonmetered*NOT SUPPORTED**NOT SUPPORTED*
Rotary Coin Drop*NOT SUPPORTED**NOT SUPPORTED*

Additional Resources