2032 F1 Reader Install Guide

Owned by David Bussman
Last updated: Jan 23, 2024 by Chris Kite
2 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Stack Washer/Dryer
Manufacturer: Dexter
Make: Dexter
Model Length: 22

Two kits need to be created. One for the washer unit, and one for the dryer unit. The only difference between these kits is the start harness.

Coin drop cover used in LC and Card Only kits is ordered through LaundryConcepts from Dexter.

Associated Models


SC0350ND17EC3XSWBCGUSA
SC0350NE17EC4XSWBCGUSA
SC0350NE17EC4XSWBCGUSX
SC0450NE17EC4XSWBCGUSA
SC0450NE17EC4XSWBCGUSX
SC0450NE17EC4XSWBCSUSA
SC0750NE16EC4RSWBCSUSA
SC0750NE17EC4XSWBCGUSA

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0010

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify that included harnesses will reach the desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Connect Power

 I-P0006

Part #: C-5213

Desc 1: Power Adapter Harness

Desc 2: DDAD - AC

   Qty: 1

Part #: C-5500-115

Desc 1: Power Extension Harness

Desc 2: 115"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the FasCard Reader Install - Universal Concepts page by connecting the C-5213 Power Adapter Harness to the power distribution panel inside the machine.

    1. 120vac: Connect the brown and blue wires to L1 and N terminal connections.

    2. 240vac: Connect the brown and blue wires L1 and L2 terminal connections.

    3. Connect the green/yellow wire to the GND terminal connection.

  2. Connect the opposite end of the C-5213 Power Adapter Harness to the C-5602R1 Power Converter.

  3. Connect the C-5500-115 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0006

Part #: C-5258

Desc 1: Coin Sense Harness (SA)

Desc 2: WCAD

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5258 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0038

Part #: C-5254

Desc 1: Machine Start Harness

Desc 2: Dexter Stack Dryer

   Qty: 1

  1. Connect the C-5254 Machine Start Harness to the Coin connection on the Machine Control Assembly.

 I-T0002

Part #: C-0127-MLV

Desc 1: Machine Start Harness

Desc 2: Dexter

   Qty: 1

  1. Connect the C-0127-MLV Machine Start Harness to the P23 connection on the Machine Control Assembly.

Connect and Mount Reader

  1. Feed the remaining harness ends through the mounting hole.

  2. (Dryer Pocket) Connect the free end of the C-5254 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. (Washer Pocket) Connect the free end of the C-0127-MLV Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  4. (Coin and Card Installation Only) Connect the free end of the C-5258 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the C-5500-115 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

CCI Software Configuration

Machine ControlPulseSerial
C-Series (1.5)SingleVend (Relay) / 55ms*NOT SUPPORTED*
C-Series (1.5)SingleVend (Relay) / 55msDexter C-Series Washer Extractor

Additional Resources