Skip to end of banner
Go to start of banner

3489 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this content. View the current version.

Compare with Current View Version History

« Previous Version 4 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Equipment Details

Type: Washer
Manufacturer: Wascomat
Make: Wascomat
Model Length: Not Set

On this page

Associated Models

WHLFP715C2DC
WHLFP715C2FMI
WHLFP715DC
WHLFP715M
WHLFP715MC2
WHLFP817M
WHLFP817MC2

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0003 (F2, Universal)
Readers: F2,FLEX,L2,F3
Install Type: Coin and Card

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to Touchscreen Reader Mounting Guide (F2 & F3) for further instructions.

 I-M0136 (Universal)
Readers: F2,FLEX,L2,F3
Install Type: Card Only

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to Touchscreen Reader Mounting Guide (F2 & F3) for further instructions.

Connect Power

 I-P0003 (Power Supply, 3 Taps, 25.5")
Readers: F1,F2,FLEX,L2,F3,FLEX RF
Install Type: [ANY]

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5210 Power Adapter Harness to the incoming power wires.

    1. 120vac: Tap and connect the blue wire to L1 and the brown wire to N.

    2. 240vac: Tap and connect the brown and blue wires to connectors L1 and L2 wires.

    3. Tap and connect the green wire to the ground wire.

  2. Connect the opposite end of the C-5210 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0042 (C-6352-40)
Readers: F2,FLEX,L2,F3,FLEX RF
Install Type: Coin and Card

Part #: C-6352-40

Desc 1: Coin Sense Harness

Desc 2: 40"

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6352-40 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0062 (C-5355)
Readers: [ANY]
Install Type: [ANY]

Part #: C-5355

Desc 1: Machine Start Harness

Desc 2: Crossover

   Qty: 1

  1. Connect the C-5355 Machine Start Harness to the CN4 connection on the Machine Control Assembly.

Connect and Mount Reader

CCI Software Configuration

Machine ControlPulseSerial
EncoreSingleVend (Relay) / 75msLaundrylux Crossover Encore

Additional Resources

  • No labels