Skip to end of banner
Go to start of banner

3286 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 4 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer
Manufacturer: Continental
Make: Continental
Model Length: 14 to 16

G-Flex Hard-Mount Washers

When setting up, customer will have to relay what extra option the machine is setup for. Select the appropriate equipment type when setting up equipment on FasCard/LaundryCard.

"Continental ProfitPlus Washer" is only a placehold/legacy equipment. New equipment should be using v45 or newer machine firmware and will require selecting on of the following:
• "Continental ProfitPlus Washer - Delicate"
• "Continental ProfitPlus Washer - Extra Spin"
• "Continental ProfitPlus Washer - Sanitize"

Associated Models


RMG033X113211111
RMG033X1132111111
RMG040X113200000
RMG040X113211100
RMG040X113211111
RMG040X1132111111
RMG040X13211111
RMG055X113211000
RMG055X113211100
RMG055X113211111
RMG055X1132111111
RMG055X11321111111
RMG055X1321111
RMG055X13211111
RMG055X213211111
RMG070X113211000
RMG070X113211111
RMG070X1132111111
RMG070X2131211111
RMG070X213211000
RMG070X213211110
RMG070X213211111
RMG070X2132111111

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

Connect Power

Connect Coin Sense Harness

 I-S0054

Part #: C-6332

Desc 1: Coin Sense Harness (SA)

Desc 2: CGI EM

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6332 Coin Sense Harness to the harness connected to the Coin Drop.

    1. Connect the Red connector to the Coin Acceptor connection, where the coin drop was previously connected, on the Machine Control Assembly.

Connect Machine Interface Harness

 I-T0017

Part #: C-0114-MLV

Desc 1: Machine Start Harness

Desc 2: Continental

   Qty: 1

  1. Connect the C-0114-MLV Machine Start Harness to the middle X1 port on the serial communication board.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole.

  2. Connect the free end of the C-0114-MLV Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

  3. (Coin and Card Installation Only) Connect the free end of the C-6332 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  4. Connect the free end of the C-5500 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

Machine Configuration

ProfitPlus Controls

  1. Connect the washer and open the door. The display will show door.

  2. Press and hold down key 1 until the Cod report appears on the display.

  3. Enter the access code into the menus by pressing the sequence of eight keys of the code without interruption. In basic configuration (when the machine is delivered) the access code to ADVANCED MODE is: 12341234.

  4. If the sequence entered is correct, the display will show Pro, corresponding to the first menu ADVANCED MODE.

  5. Keys 2 and 4 allow the selection of the precedent table menus. The menu selected is shown on the display following its keyword. To enter in it, press key 1 when displaying it.

  6. Navigate to Mod > ID and set value to '1'.

  7. Exit ADVANCE MODE.

CCI Software Configuration

Machine ControlPulseSerial
ProfitPlusSingleVend (Relay) / 500msContinental ProfitPlus Washer

Additional Resources

  • No labels