0435 F1 Reader Install Guide

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer
Manufacturer: Whirlpool
Make: Whirlpool
Model Length: Not Set

Associated Models

CAM2752RQ0
CAM2752TQ
CAM2752TQ2
CAM2752TQ3
CAM2762RQ0
CAM2762TQ
CAM2762TQ0
CAM2762TQ2
CAM2762TQ3

Recommended Tools and Supplies

Drill
1 1/8" Tungsten Carbide Tipped Hole Cutter
Cutting Oil
9/64" Drill Bit
Center Punch
Hammer
Fine Point Permanent Marker
Pliers
Tape Measure

Installation

Install Mounting Hardware

I-M0067

Part #: C-0301

Desc 1: Topload Mounting Bolt

Desc 2:

Qty: 1

Part #: C-5771

Desc 1: Metercase Bracket

Desc 2: Coin Drop Ready Machines

Qty: 1

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

Qty: 2

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

Qty: 1

Remove existing coin box and coin slide.
Install the C-5771 Metercase Bracket over the front of the metercase.
Secure in place using the C-0301 Topload Mounting Bolt.

Connect Power

I-P0004

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

Qty: 1

Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Kit 0 does not exist

Connect Machine Interface Harness

I-T0021

Part #: C-0116-MEC

Desc 1: Machine Start Harness

Desc 2: Mechanical Harness

Qty: 1

Connect the C-0116-MEC Machine Start Harness 6-pin connector at the Coin Box area.
1. Connect the 2-pin connector of the harness under the faceplate, near display/controls.

Connect and Mount Reader

Feed remaining harness ends through the mounting hole as described in the F1: FasCard Reader Mounting Guide.
Connect the free end of the C-0116-MEC Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.
Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

CCI Software Configuration

Microsoft VBScript runtime

error '800a01a8'

Object required: 'g_objInstallRef.ReaderInterfaces.Item(...)'

/intranet/includes/classes/installref/Equipment_Control.asp, line 65

Machine Control	Pulse	Serial
NO NAME	SingleVend (Relay) / 40000