Skip to end of banner
Go to start of banner

3294 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 4 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer
Manufacturer: Continental
Make: Continental
Model Length: 12

L-Series Hard-Mount Washers

Associated Models

L1018CM11300
L1018CM21310
L1018CR21510
L1030CM11310
L1030CM21310
L1030CR21510
L1040CM11310
L1040CM21310
L1040CR11510
L1040CR21310
L1040CR21510
L1050CM11310
L1050CM21310
L1075CM11111
L1075CM21010
L1075CM21310
L1075CM21313
L1075CM21320
L1075CR11111
L1075CR21510
L1125CM13200
L1125CM21300
L1125CM21310
L1125CM21320
L1125CM21329
L1125CM23000

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0010

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

 I-M0164

Part #: C-0900

Desc 1: Drop Cover

Desc 2: Continental

   Qty: 1

Part #: C-1013

Desc 1: Nut

Desc 2: 6-32 - Kep

   Qty: 4

Part #: C-0936

Desc 1: Vault Mount Bracket

Desc 2:

   Qty: 1

Part #: C-0134

Desc 1: Standoff

Desc 2: 8-32" x 1" - Hex

   Qty: 2

Part #: C-0146

Desc 1: Screw

Desc 2: 8-32 x 1-1/4" - Cap

   Qty: 2

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

  1. Remove coin drop and install C-0900 Drop Cover.

    1. Secure with C-1013 Nut.

  2. Spread the C-0936 Vault Mount Bracket wings outward before insertion to lock bracket into place.

  3. Insert the C-0936 Vault Mount Bracket into the coin vault.

  4. Attach C-0134 Standoffs to the C-0936 Vault Mount Bracket.

  5. Secure reader to the C-0936 Vault Mount Bracket using C-0146 Screws.

 I-M0003

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

 I-M0128

Part #: C-0144

Desc 1: Screw

Desc 2: 8-32 x 2" - Flat

   Qty: 2

Part #: C-0900

Desc 1: Drop Cover

Desc 2: Continental

   Qty: 1

Part #: C-1013

Desc 1: Nut

Desc 2: 6-32 - Kep

   Qty: 4

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

Part #: C-6936

Desc 1: F2, Sm Vault Mount Bracket

Desc 2:

   Qty: 1

  1. Remove coin drop and install C-0900 Drop Cover.

    1. Secure using the (4) C-1013 6-32 Keps Nuts.

  2. Spread the C-6936 Vault Mount Bracket wings outward before insertion to lock bracket into place.

  3. Insert the C-6936 Vault Mount Bracket into the coin vault.

  4. Secure the C-5414 F2 Mounting Bracket to the C-6936 Vault Mount Bracket with the (2) C-0144 8-32 x 2" Screws.

Connect Power

 I-P0003

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  2. Connect the C-5210 Power Adapter Harness to the installed spade taps.

  3. Connect the C-5210 Power Adapter Harness to the C-5602 Power Converter.

  4. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

  5. Connect the opposite end of the C-5210 Power Adapter Harness to the C-5602 Power Converter.

  6. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-C0004

Part #: C-5334

Desc 1: Combination Harness

Desc 2: CGI CM

   Qty: 1

  1. Disconnect the existing wires from the Coin Drop and connect the C-5334 Combination Coin/Start Harness to the Coin Drop.

    1. Blue wires go to common (Co) and normally open (NO) on coin switch.

 I-C0006

Part #: C-5335

Desc 1: Combination Harness

Desc 2: CGI CR

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5335 Combination Harness (3-pin, black connector) to the Coin Eye Sensor.

    1. The White wire (female) spade connectors bundled with the black connector attach to the Coin Block solenoid.

 I-C0013

Part #: C-6334

Desc 1: Combination Harness

Desc 2: CGI CM

   Qty: 1

  1. Disconnect the existing wires from the Coin Drop and connect the C-6334 Combination Coin/Start Harness to the Coin Drop.

    1. Blue wires go to common (Co) and normally open (NO) on coin switch.

 I-C0015

Part #: C-6335

Desc 1: Combination Harness

Desc 2: CGI CR

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6335 Combination Harness (3-pin, black connector) to the Coin Eye Sensor.

    1. The White wire (female) spade connectors bundled with the black connector attach to the Coin Block solenoid.

Connect Machine Interface Harness

 I-C0004

Part #: C-5334

Desc 1: Combination Harness

Desc 2: CGI CM

   Qty: 1

  1. Disconnect the existing wires from the Coin Drop.

    1. Connect the C-5334 to the Coin Drop.

    2. Connect the Violet wires to Blue wires 36 & 35.

    3. White wires wrapped with Violet go to Red wires 207 & 30.

    4. White wires wrapped with Blue go to Brown coin blocking solenoid wires.

      1. Wrap the connectors in electrical tape to keep the bare terminals from exposing.

 I-C0006

Part #: C-5335

Desc 1: Combination Harness

Desc 2: CGI CR

   Qty: 1

  1. Connect the Violet wire (male) spade connectors to the Coin Sense Input.

  2. Connect the remaining White wire (male) spade connectors to the Coin Block solenoid drive.

 I-C0013

Part #: C-6334

Desc 1: Combination Harness

Desc 2: CGI CM

   Qty: 1

  1. Disconnect the existing wires from the Coin Drop.

    1. Connect the C-6334 Machine Start Harness to the Coin Drop.

    2. Connect the Violet wires to Blue wires 36 & 35.

    3. White wires wrapped with Violet go to Red wires 207 & 30.

    4. White wires wrapped with Blue go to Brown coin blocking solenoid wires.

      1. Wrap the connectors in electrical tape to keep the bare terminals from exposing.

 I-C0015

Part #: C-6335

Desc 1: Combination Harness

Desc 2: CGI CR

   Qty: 1

  1. Connect the Violet wire (male) spade connectors to the Coin Sense Input.

  2. Connect the remaining White wire (male) spade connectors to the Coin Block solenoid drive.

Connect and Mount Reader

 LaundryCard Reader (C-0100, C-0101, C-0102, C-0103)

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  5. Secure the LaundryCard reader to the bracketry using included hardware.

 LaundryCard L2 Reader (C-0103-L2)

L2_Port_Guide.png

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Power Harness to port 1.

  5. Secure the L2 reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F1 Reader (C-5001)

  1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Mounting Guide.

  2. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  3. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

  6. Secure the FasCard reader to base as described in the F1 Reader Mounting Guide.

 F2/FLEX Reader (C-5401, C-5402, C-5402E)

  1. Feed remaining harness ends through the mounting hole as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

  2. For Serial Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

  3. For Pulse Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    1. For dual coin drop setups connect the secondary Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Harness to port 1.

  6. Secure the FasCard reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F3 Reader (C-5520, C-5520E)

TODO

CCI Software Configuration

Machine ControlPulseSerial
Coin MicroSingleVend (Relay) / 500ms*NOT SUPPORTED*
Coin RotarySingleVend (Relay) / 500ms*NOT SUPPORTED*

Additional Resources

  • No labels