Skip to end of banner
Go to start of banner

0578 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 3 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Tumble Dryer (Stack)
Manufacturer: Dexter
Make: Dexter
Model Length: Not Set

Associated Models


DDAD30KCA
DDAD30KCA65
DDAD30KCA65EC
DDAD30KCB65
DDAD30KCB65CN
DDAD30KCB65CNTS
DDAD30KCB65NC
DDAD30KCB65TS
DDAD30KCB65US
DDAD30KCB65USTS
DDAD30KCK
DDAD30KCS
DDAD30KCS65
DDAD30KCS65CN
DDAD30KCS65EC
DDAD30KCS65ECTS
DDAD30KCS65TS
DDAD30KCS65US
DDAD30KCS65USTS
DDAD30KCW
DDAD30KCW65
DDAD30KCW65CN
DDAD30KCW65CP
DDAD30KCW65EC
DDAD30KCW65US
DDAD30KCX65CN
DDAD30KCX65US
DDAD30KCY65CN
DDAD30KCY65US
DDAD30KCY65USPS
DDAD30KCZ65US
DDAD50KCA65
DDAD50KCA65EC
DDAD50KCB65CN
DDAD50KCB65CNTS
DDAD50KCS
DDAD50KCS65
DDAD50KCS65CP
DDAD50KCS65EC
DDAD50KCS65TS
DDAD50KCS65US
DDAD50KCW65
DDAD50KCW65CN
DDAD50KCW65EC
DDAD50KCW65TS
DDAD50KCX65US
DDAD50KCY65US
DDAD50KCY65USTS
DDAG30KCS65
DDAG30KCW65
DDTD30KCS
DDTD30KCS65
DDTD30KCS65ECXC
DDTD30KCS65XC
DDTD30KCW65ECXC
DDTD30KCW65XC

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0104

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

 I-M0105

Part #: C-0144

Desc 1: Screw

Desc 2: 8-32 x 2" - Flat

   Qty: 2

Part #: C-0905

Desc 1: Drop Cover

Desc 2: 2-3/8" x 4-5/8"

   Qty: 1

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

Part #: C-6936

Desc 1: F2, Sm Vault Mount Bracket

Desc 2:

   Qty: 1

  1. Feed the harness ends through the coin vault opening and then through the circular opening in the C-6936 Vault Mount Bracket.
  2. Spread the C-6936 Vault Mount Bracket wings outward and then insert the C-6936 Vault Mount Bracket into the coin vault.
  3. Feed the harness ends through the C-5414 F2 Mounting Bracket.
  4. Secure the C-5414 F2 Mounting Bracket to the C-6936 Vault Mount Bracket with the C-0144 Screws.
  5. Install the C-5710 Rubber Grommet into the circular opening of the C-5414 F2 Mounting Bracket.
  6. Remove any existing coin drop.
  7. Mount the C-0905 Drop Cover using existing mounting hardware where the coin drop was previously installed.

Connect Power

 I-P0006

Part #: C-5213

Desc 1: Power Adapter Harness

Desc 2: DDAD - AC

   Qty: 1

Part #: C-5500-115

Desc 1: Power Extension Harness

Desc 2: 115"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5213 Power Adapter Harness to the power distribution panel inside the machine.

    1. 120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    2. 240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    3. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-5213 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500-115 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0031

Part #: C-6253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.
 I-S0050

Part #: C-6382

Desc 1: Coin Sense Harness

Desc 2: Imonex EM100/EM3

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6382 Coin Sense Harness to the harness connected to the Coin Drop.
 I-S0031

Part #: C-6253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6258 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0038

Part #: C-5254

Desc 1: Machine Start Harness

Desc 2: Dexter Stack Dryer

   Qty: 1

  1. Connect the C-5254 Machine Start Harness to the P3 connector on the Machine Control Assembly.
 I-T0040

Part #: C-5256

Desc 1: Machine Start Harns (pulse)

Desc 2: 20" - Male taps, Rq. Female

   Qty: 1

  1. Connect the C-5256 Machine Start Harness to the harness previously connected to the coin drop micro switch.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.
  2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-115 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

CCI Software Configuration

Machine ControlPulseSerial
A-Series (1.0)SingleVend (Relay) / 55ms*NOT SUPPORTED*

Additional Resources

  • No labels