Skip to end of banner
Go to start of banner

3208 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 3 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Vending
Manufacturer: Wittern
Make: Wittern
Model Length: Not Set

This entry covers a large portion of Wittern machines. As they all share the same installation requirements and only slightly vary. Photos are not applicable to all models.

Associated Models

3503
3535
3536
3537
3538
3539
3573
3574
3575
3576
3578
36 SELECT LAUNDRY CENTER
FEDERAL MACHINE: 25/27/28 SELECT
FEDERAL MACHINE: 30/40/45 SELECT
MERCATO 5000
MZF3000
USI: ALPINE 5000 ELEVATOR
USI: ALPINE ST3000/VT3000
USI: ALPINE ST5000/VT5000
USI: WS3000/WS4000/WS5000/WS6000

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0174

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to Touchscreen Reader Mounting Guide (F2 & F3) for further instructions.

 I-M0178

Part #: C-0939

Desc 1: Bill Acceptor Cover

Desc 2:

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Optional: Remove existing payment device and cover opening using C-0939 BNA Cover Plate.

  2. Place the C-6700-TEMP Drill Template on the desired mounting location.

    1. If C-0939 BNA Cover Plate is used, drilling mounting holes into the plate is recommended if able.

  3. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  4. Refer to Touchscreen Reader Mounting Guide (F2 & F3) for further instructions.

Connect Power

Power is supplied through the same Machine Interface Harness described in step 4.

Connect Coin Sense Harness

Not applicable in this setup. FasCard reader does not collect payment from any other devices, and will only send funds to the machine's control.

Connect Machine Interface Harness

 I-C0020

Part #: C-6124-MDB

Desc 1: Machine Start Harness

Desc 2: F2 MDB Interface Harness

   Qty: 1

  1. Connect the C-6124-MDB Machine Start Harness to the MDB connection on the Machine Control Assembly.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole as described in the FasCard Mounting Guide.
  2. Connect the black, 10-pin connection of the C-6124-MDB Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. Connect the clear, 3-pin connection of the C-6124-MDB Power Harness to port 1.
  4. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

CCI Software Configuration

Machine ControlPulseSerial
MDB*NOT SUPPORTED*Vending - MDB Level 1

Additional Resources

  • No labels