Skip to end of banner
Go to start of banner

3619 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 12 Current »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Small Dryer (Stack)
Manufacturer: Alliance
Make: Speed Queen
Model Length: 8

Associated Models


BSE907WF
HSET17WF
SSE107WF
SSE907WF
SSE917WF
SSET07WF
SSG109WF
SSG119WF
SSG909WF
SSGT09WF
SSGT19WF
SSGY09WF
SSGY19WF

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Connect Machine Interface Harness

 I-T0008

Part #: C-0109R1

Desc 1: Machine Start Harness

Desc 2: Red / White w. Capacitor

   Qty: 1

  1. Connect the C-0109R1 Machine Start Harness to the Coin1 connection harness on the Machine Control Assembly.

 I-T0012

Part #: C-0110-TOP

Desc 1: Machine Start Harness

Desc 2: 36" - Alliance Pre-ACA

   Qty: 1

Part #: C-0110-CP

Desc 1: Jumper Plug

Desc 2: Enables card mode on pre-ACA

   Qty: 1

Pulse Setup

  1. Connect the C-0110-TOP Machine Start Harness to the H5 connection on the Machine Control Assembly.

  2. C-0110-CP Jumper Plug is not used, but can be retained in case of future serial communication usage usage.

Serial Setup

  1. Connect the C-0110-TOP Machine Start Harness to the H5 connection on the Machine Control Assembly.

  2. Connect the C-0110-CP Jumper Plug to the H2 connection on the Machine Control Assembly.

 I-T0015

Part #: C-0112R1

Desc 1: Machine Start Harness

Desc 2: Alliance EDC

   Qty: 1

  1. Connect the C-0112R1 Machine Start Harness to the H2 connector on the Machine Control Assembly.

 I-T0040

Part #: C-5256

Desc 1: Machine Start Harns (pulse)

Desc 2: 20" - Male taps, Rq. Female

   Qty: 1

  1. Connect the C-5256 Machine Start Harness to the harness previously connected to the micro switch on the coin drop/slide.

 I-T0049

Part #: C-5300-NC

Desc 1: Machine Start Harness

Desc 2: Aliiance - Normally Closed

   Qty: 1

  1. Connect the C-5300-NC Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.

Connect Power

 I-P0003

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0001

Part #: C-5250

Desc 1: Coin Sense Harness

Desc 2:

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.

 I-S0004

Part #: C-5253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5253 Coin Sense Harness to the harness connected to the Coin Drop.

 I-S0027

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: F2

   Qty: 1

  1. Disconnect the Coin Drop from the machine control assembly.

  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

 I-S0031

Part #: C-6253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

  1. Disconnect the factory harness from the micro switch tabs on the Coin Drop.

  2. Connect the C-6253 Coin Sense Harness to the micro switch tabs in any pairing.

Connect Machine Interface Harness

 I-T0008

Part #: C-0109R1

Desc 1: Machine Start Harness

Desc 2: Red / White w. Capacitor

   Qty: 1

  1. Connect the C-0109R1 Machine Start Harness to the Coin1 connection harness on the Machine Control Assembly.

 I-T0012

Part #: C-0110-TOP

Desc 1: Machine Start Harness

Desc 2: 36" - Alliance Pre-ACA

   Qty: 1

Part #: C-0110-CP

Desc 1: Jumper Plug

Desc 2: Enables card mode on pre-ACA

   Qty: 1

Pulse Setup

  1. Connect the C-0110-TOP Machine Start Harness to the H5 connection on the Machine Control Assembly.

  2. C-0110-CP Jumper Plug is not used, but can be retained in case of future serial communication usage usage.

Serial Setup

  1. Connect the C-0110-TOP Machine Start Harness to the H5 connection on the Machine Control Assembly.

  2. Connect the C-0110-CP Jumper Plug to the H2 connection on the Machine Control Assembly.

 I-T0015

Part #: C-0112R1

Desc 1: Machine Start Harness

Desc 2: Alliance EDC

   Qty: 1

  1. Connect the C-0112R1 Machine Start Harness to the H2 connector on the Machine Control Assembly.

 I-T0040

Part #: C-5256

Desc 1: Machine Start Harns (pulse)

Desc 2: 20" - Male taps, Rq. Female

   Qty: 1

  1. Connect the C-5256 Machine Start Harness to the harness previously connected to the micro switch on the coin drop/slide.

 I-T0049

Part #: C-5300-NC

Desc 1: Machine Start Harness

Desc 2: Aliiance - Normally Closed

   Qty: 1

  1. Connect the C-5300-NC Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.

Extras

No EXTRAS kits exist for this equipment.

Connect and Mount Reader

 LaundryCard Reader (C-0100, C-0101, C-0102, C-0103)

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  5. Secure the LaundryCard reader to the bracketry using included hardware.

 LaundryCard L2 Reader (C-0103-L2)

L2_Port_Guide.png

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Power Harness to port 1.

  5. Secure the L2 reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F1 Reader (C-5001)

  1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Mounting Guide.

  2. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  3. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

  6. Secure the FasCard reader to base as described in the F1 Reader Mounting Guide.

 F2/FLEX Reader (C-5401, C-5402, C-5402E)

  1. Feed remaining harness ends through the mounting hole as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

  2. For Serial Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

  3. For Pulse Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    1. For dual coin drop setups connect the secondary Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Harness to port 1.

  6. Secure the FasCard reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F3 Reader (C-5520, C-5520E)

TODO

CCI Software Configuration

Machine ControlPulseSerial
CAM Timer*NOT SUPPORTED**NOT SUPPORTED*
Coin Slide Hybrid (Pulse)SingleVend (Relay) / 500ms*NOT SUPPORTED*
EDCSingleVend (Relay) / 80ms*NOT SUPPORTED*
MDC (Vended)SingleVend (MLV+) / 80msAlliance MDC Small Dryer
NetMasterSingleVend (Relay) / 80ms*NOT SUPPORTED*

Additional Resources

  • No labels