This page provides the installer with information on the the various FasCard Touch Kiosk install configurations. Including electrical requirements, unit specifications, and mounting instructions.
Required parts
| Part ID | Description |
|---|---|
| C-5610R1 |
Optional parts & hardware
| Part ID | Description |
|---|---|
| C-5623 | |
| C-5626 | |
| C-5628 |
- Uninterruptible Power Supply (UPS) (not included)
- Compression anchor (not included)
- 1/4" lag screw or anchor (not included)
- Wall mount brackets (not included)
- 1/8" to 1/4" shims (not included)
Touch Kiosk specifications and requirements
Kiosk dimensions
The FasCard Touch Kiosk can be mounted in or on an existing wall or can be pedestal mounted. It offers end-users a convenient way to view and manager their Loyalty account, add balance to an existing card, or obtain a new card.
| Touch Kiosk | Touch Kiosk Drawer | Kiosk Pedestal Spacer | Kiosk Pedestal Base | |
|---|---|---|---|---|
| Dimensions |
|  |
|
|
| CCI Part # | C-5610R1 | C-5623 | C-5626 | C-5628 |
| Description | Main Kiosk body, can be pedestal or wall mounted. | Drawer addition to main Kiosk body, can be pedestal or wall mounted. | Kiosk pedestal spacer, not required for wall mount. | Kiosk pedestal, not required for wall mount. |
Electrical Requirements
Always follow local electrical codes.
The FasCard Touch Kiosk operates on 120VAC and comes with a standard 12' grounded power cord. The bottom of the base has a 1/2" knock out that can be used to mount a standard 120VAC power outlet inside the base. Additional holes may be drilled to accommodate other conduit sizes. Card Concepts Inc. recommends using an outlet with an isolated ground and that an Uninterruptible Power Supply (not included) be used to protect the kiosk from power fluctuations and outages.
Unpacking the Touch Kiosk
The Touch Kiosk is packaged in a corrugated shipping assembly with an upper and lower tray as well as a protective front panel and shipping carton. Use caution when cutting securing straps and packing tape.
To view the step by step guide to unpacking the Touch Kiosk, click the arrow adjacent to the header titled "Unpacking the Touch Kiosk - Step by Step".
Mounting the Touch Kiosk
Choose one of the following tabs, based on the mounting configuration you are installing.
Disconnect any electrical device from power before performing any work on the device. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks.
Card Concepts Inc. takes no responsibility for the accuracy of this document or any damage that may occur to target equipment. Technical Support recommends using all appropriate safety equipment (such as hand and eye protection) during execution of the instructions below.
Activate the Touch Kiosk
Need help?
If you are facing any issues or have questions about the information contained within this document, please call us at 630-930-5115. You can also reach us by email at support@laundrycard.com.
- Configure the Touch Kiosk equipment type on the FasCard Admin Site - Equipment Setup page.
- Add the Touch Kiosk to the machine list with an appropriate reader address on the FasCard Admin Site - Machine Setup page.
- Connect the power cable that was fed upwards into the cabinet during installation.
- Flip the rocker switch so that the "I" is depressed.
- The internal LED lights will indicate power is being received and the Bill Note Acceptor (BNA) will cycle.
- When power is turned on for the first time, the Kiosk will boot to an addressing screen.
Use the on-screen keypad to assign the Touch Kiosk address you assigned in Step 2.
If the incorrect address is entered, change the address by following the steps on the Touch Kiosk Operation and Maintenance page under the 'Maintenance Menu Options' header.
- Use the Enter button to confirm the value of the digit and proceed to the next digit.
- After confirming the third digit, the FasCard Kiosk will begin downloading its designated firmware files.
- Once the download and installation processes have finished, the Kiosk will load its user screen.
Additional documentation