3620 Reader Install Guide

Owned by Chris Kite
Last updated: Jan 26, 2024 by CCI Integration User
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Vending
Manufacturer: Jofemar
Make: Jofemar
Model Length: Not Set

Associated Models

COFFEEMAR250
COFFEEMAR546
COFFEEMARG250
COFFEEMARG546
G250
G546

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Connect Power

 I-P0012

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500-60

Desc 1: Power Extension Harness

Desc 2: 60"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap the machine AC power wires using the C-5101 Spade Taps. See FasCard Reader Install - Universal Concepts for more details.

    1. For 120vac models: L1, N, and Ground wires

    2. For 240vac models: L1, L2, and Ground wires

  2. Connect the three wires from the C-5210 Power Adapter Harness to the C-5101 Spade Taps.

    1. Connect the Blue wire to the L1 tap.

    2. Connect the Brown wire to the N/L2 tap.

    3. Connect the Green/Yellow wire to the Ground tap.

  3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connector on the C-5602R1 Power Converter.

  4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connector on the C-5500-60 Power Extension Harness.

  5. Run the C-5500-60 Power Extension Harness to the reader mounting location.

 I-C0020

Part #: C-6124-MDB

Desc 1: Machine Start Harness

Desc 2: F2 MDB Interface Harness

   Qty: 1

  1. Connect the male, 6-pin connector from the C-6124-MDB Machine Start Harness to the MDB connection on the Machine Control Assembly.

  2. Optional (FasCard Only): Use the female, 6-pin pigtail connector from the C-6124-MDB to reconnect any existing payment devices.

Power is supplied through the same Machine Interface Harness described in step 4.

Connect Coin Sense Harness

No COIN SENSE kits exist for this equipment.

Not applicable in this setup. FasCard reader does not collect payment from any other devices, and will only send funds to the machine's control.

Connect Machine Interface Harness

 I-T0071

Part #: C-0124-MLV

Desc 1: Machine Start Harness

Desc 2: MDB Communication

   Qty: 1

  1. Connect the C-0124-MLV Machine Start Harness to the MDB connector on the Machine Control Assembly.

  2. FasCard Only: Use the pigtail connection to reconnect existing devices.

 I-C0020

Part #: C-6124-MDB

Desc 1: Machine Start Harness

Desc 2: F2 MDB Interface Harness

   Qty: 1

  1. Connect the male, 6-pin connector from the C-6124-MDB Machine Start Harness to the MDB connection on the Machine Control Assembly.

  2. Optional (FasCard Only): Use the female, 6-pin pigtail connector from the C-6124-MDB to reconnect any existing payment devices.

CCI Software Configuration

Machine ControlPulseSerial
MDB*NOT SUPPORTED*Vending - MDB Level 1

Additional Resources