0831 Reader Install Guide

Owned by Chris Kite
Last updated: Jan 26, 2024 by CCI Integration User
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Tumble Dryer (Stack)
Manufacturer: Alliance
Make: [VARIES]
Model Length: 15

Associated Models


JT0300DFGEC3456
JT0300DFGECW015
JT0300DRGEC0111
JT0300DRGECL001
JT0300DRGECN001
JT0300DRGECN004
JT0300DRGECN032
JT0300DRGECW001
JT0300DRGECW003
JT0300DRGEXW001
JT0300DRGEYW005
ST0300DFGECL008
ST0300DRGEC1234
ST0300DRGECC001
ST0300DRGECL001
ST0300DRGECLO00
ST0300DRGECW001
ST0300DRGEP1234
ST0300DRGEYW005
ST0300DRGZCN001
ST0300DRGZCW001
ST0300DRGZCW010
ST0300DRGZCW011
ST0300DRGZCWOO1
ST0300DRGZRL002
ST0300DRGZRW001

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Connect Power

 I-P0008

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500-84

Desc 1: Power Extension Harness

Desc 2: 84"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

  3. Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0001

Part #: C-5250

Desc 1: Coin Sense Harness

Desc 2:

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.

 I-S0027

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: F2

   Qty: 1

  1. Disconnect the Coin Drop from the machine control assembly.

  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

CCI Software Configuration

Machine ControlPulseSerial
EDCSingleVend (Relay) / 80ms*NOT SUPPORTED*
NetMasterSingleVend (Relay) / 80ms*NOT SUPPORTED*
Nonmetered*NOT SUPPORTED**NOT SUPPORTED*
Rotary Coin Drop*NOT SUPPORTED**NOT SUPPORTED*

Additional Resources