3599 Reader Install Guide

Owned by Chris Kite
Last updated: Jan 26, 2024 by CCI Integration User
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Small Dryer (Stack)
Manufacturer: Alliance
Make: [VARIES]
Model Length: 15

Associated Models


SSGNCFGW113TW01

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Connect Power

 I-P0002

Part #: C-6204-40

Desc 1: Power Adapter Harness

Desc 2: F2, 12vDC Pow Harness - 40"

   Qty: 1

  1. Connect the C-6204-40 12VDC Power Harness to the H10 connection on the Machine Control Assembly.

    h10.jpg

  2. Connect the green wire to a chassis ground.

  3. The remaining end (3-pin molex) connects directly to the rear of the FasCard Reader.

Connect Coin Sense Harness

 I-S0001

Part #: C-5250

Desc 1: Coin Sense Harness

Desc 2:

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.

 I-S0027

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: F2

   Qty: 1

  1. Disconnect the Coin Drop from the machine control assembly.

  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0003

Part #: C-5240

Desc 1: Machine Start Harness

Desc 2: Alliance ACA

   Qty: 1

  1. Connect the C-5240 Machine Start Harness to the the H3 connection on the Machine Control Assembly or Communication board.

Extras

 I-X0008

Part #: C-5240

Desc 1: Machine Start Harness

Desc 2: can use C-5240-144

   Qty: 1

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: can use C-6250-144

   Qty: 1

Part #: C-6401

Desc 1: Stack Add On Board - MLV

Desc 2: Serial / MultiVend

   Qty: 1

  1. Run C-5240 Machine Start Harness and C-6250 Coin Sense Harness to the second Machine Control Assembly.

  2. Connect C-5240 Machine Start Harness to the H3 connection and the C-6250 Coin Sense Harness to the Coin 1 connection on the second Machine Control Assembly.

  3. Connect the C-6401 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.

    1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Unit 1 on the Stack Add-on Board.

    2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Unit 2 on the Stack Add-on Board.

  4. Connect the Coin Sense Harness connected to the upper pocket Coin Drop to port 3 (Coin 1 Sense Harness Connection Port) on the F2 reader.

  5. Connect the Coin Sense Harness connected to the lower pocket Coin Drop to port 4 (Coin 2 Sense Harness Connection Port) on the F2 reader.

Machine Configuration

ACA machines using a serial configuration require dip switch 3 on the Machine Control Board to be set to the 'ON' position. Leave all other dip switches as is.

CCI Software Configuration

Machine ControlPulseSerial
Quantum+ (A4)SingleVend (MLV+) / -80msAlliance ACA H7S Small Dryer A4 - Quantum+

Additional Resources